I'm always looking for toppers that will work with my casual lifestyle. Now while I'm drawn to very tailored jackets, realistically they don't fit into my work life. So when I saw this McCalls pattern in the fall offerings, I thought it would fit well in my wardrobe...
![]()
![]()
Even though this pattern has several sleeve variations, I'm sticking with the kimono type sleeves because I like simplier silhouettes. Refer to my sentence above about tailored jackets. I really am a classic silhouette loving sewist who likes bright colors and prints. This pattern gives me a great layering piece, which I need for the winter. It's simple, classic and stylish.
![]()
Supply List ~
Blue/Black Jacquard from Elliott Berman Fabrics
12 yds black bias binding from Pacific Trimmings
1 small snap
Pattern Alterations ~
- The shoulder seams were shortened by an inch
- Did a pivot and slide to add 3" at the hemline and 2" at the hip area
- Added inseam pockets from McCalls 7481
Construction Info ~
This is a simple sew and it goes together quickly. There are four pattern pieces - back, front, sleeve and sash. The time consuming element is the bias binding...and that's what drew me to the pattern.
I did add some time to the construction by adding pockets after I sewn the side seams. So everything had to be ripped open and sewn again. Because I used big and deep pockets, I had to hand stitch them to the jacket front so they wouldn't flop around inside the jacket.
![]()
The bias binding was applied using the Hong Kong method. The pattern tells you to fold it in half and sew it down. I wanted a cleaner look. Applying it using the Hong Kong application means that the bias is longer on the inside. Stitching in the ditch causes it to have a more finished look on the jacket front.
I also added some ribbon ties from the bias binding to the side of and the front of the jacket to tie it together. I wanted to insure that the belt wasn't the only thing holding the jacket together.
A snap was sewn to the v-neck junction at the front of the jacket. This helps the v-neckline to lay flat. To me all of these additions enhance the wearability of the jacket.
![]()
After I added the snaps I noticed that the left side hangs a little lower than the right. I was going to fix it but I like the quirkiness of it, so left it. When you're looking at the pictures below realize that the fronts not meeting is deliberate.
A Few Pictures ~
![]()
![]()
![]()
![]()
![]()
The fabric is what makes this jacket work. I suggest if you make one for yourself that you use a bold fabric (like the pattern envelope) or a denim so that the jacket is distinctive. Your bias binding can be coordinating (like mine) or contrasting to add even more pop! Also, buy more bias binding than the pattern recommends. I bought 13 yards and used 12.
This is where I tell you that Elliott Berman supplied the fabric as part of my Brand Ambassadorship with them. If you're interested in purchasing fabric similar to the one I used, check out their new french jacquards here. One more thing about the fabric, it's warm. I'm looking forward to pairing this with other turtlenecks during the cold months of January through March.
I would make this again...probably in denim. Though I will have to adjust the pattern fronts. To achieve the look on the pattern envelope, I need a little more fabric across the front. Even though I'm fine with the way this one hangs. But if I do make it again, I will definitely make the adjustments.
Even with that I highly recommend purchasing this pattern. It's a simple sew especially if you don't add all the elements I did. The finished jacket has a lot of bang for the buck and I'm sure it will get a lot of wear this winter.
...as always more later!
Even though this pattern has several sleeve variations, I'm sticking with the kimono type sleeves because I like simplier silhouettes. Refer to my sentence above about tailored jackets. I really am a classic silhouette loving sewist who likes bright colors and prints. This pattern gives me a great layering piece, which I need for the winter. It's simple, classic and stylish.
Supply List ~
Blue/Black Jacquard from Elliott Berman Fabrics
12 yds black bias binding from Pacific Trimmings
1 small snap
Pattern Alterations ~
- The shoulder seams were shortened by an inch
- Did a pivot and slide to add 3" at the hemline and 2" at the hip area
- Added inseam pockets from McCalls 7481
Construction Info ~
This is a simple sew and it goes together quickly. There are four pattern pieces - back, front, sleeve and sash. The time consuming element is the bias binding...and that's what drew me to the pattern.
I did add some time to the construction by adding pockets after I sewn the side seams. So everything had to be ripped open and sewn again. Because I used big and deep pockets, I had to hand stitch them to the jacket front so they wouldn't flop around inside the jacket.
The bias binding was applied using the Hong Kong method. The pattern tells you to fold it in half and sew it down. I wanted a cleaner look. Applying it using the Hong Kong application means that the bias is longer on the inside. Stitching in the ditch causes it to have a more finished look on the jacket front.
I also added some ribbon ties from the bias binding to the side of and the front of the jacket to tie it together. I wanted to insure that the belt wasn't the only thing holding the jacket together.
A snap was sewn to the v-neck junction at the front of the jacket. This helps the v-neckline to lay flat. To me all of these additions enhance the wearability of the jacket.
After I added the snaps I noticed that the left side hangs a little lower than the right. I was going to fix it but I like the quirkiness of it, so left it. When you're looking at the pictures below realize that the fronts not meeting is deliberate.
A Few Pictures ~
The fabric is what makes this jacket work. I suggest if you make one for yourself that you use a bold fabric (like the pattern envelope) or a denim so that the jacket is distinctive. Your bias binding can be coordinating (like mine) or contrasting to add even more pop! Also, buy more bias binding than the pattern recommends. I bought 13 yards and used 12.
This is where I tell you that Elliott Berman supplied the fabric as part of my Brand Ambassadorship with them. If you're interested in purchasing fabric similar to the one I used, check out their new french jacquards here. One more thing about the fabric, it's warm. I'm looking forward to pairing this with other turtlenecks during the cold months of January through March.
I would make this again...probably in denim. Though I will have to adjust the pattern fronts. To achieve the look on the pattern envelope, I need a little more fabric across the front. Even though I'm fine with the way this one hangs. But if I do make it again, I will definitely make the adjustments.
Even with that I highly recommend purchasing this pattern. It's a simple sew especially if you don't add all the elements I did. The finished jacket has a lot of bang for the buck and I'm sure it will get a lot of wear this winter.
...as always more later!